The powerful 5808LST is a combination wireless photoelectric smoke
and heat detector that trips when temperatures reach 135º F. Ideal for difficult
to wire locations, situations where room aesthetics are critical or where
hazardous materials exist, the 5808LST provides the ultimate in installation
flexibility.

Remarkably cost-effective, the attractive, low profile unit blends
easily with any décor and provides benefits rarely found in smoke detectors in
this price range. Smart Check™ remote maintenance reporting automatically alerts
the central station when it is in need of service, and built-in drift
compensation continuously corrects sensitivity variances caused by dust. The
5808LST is UL 268 listed for use in both commercial and residential
applications.

Features

• Low profile housing
• Extended battery life – Two 3V Lithium
• Automatic drift compensation
• Smart Check™ – pre-alarm maintenance signal
• Test/alarm silence button – Immediate signal 2.5 sec delay
  horn activation
• Field replaceable chamber
• Heat Detector – dual 135° thermistors
• Low temperature alert signal
• Temporal Code 3 sounder
• Pre-Low battery signal to central station (if applicable)
  seven days prior to horn chirp
• UL 268 – Commercial and
  Residential

• 
  
  
  
  
  

  
  
  

  5809

  Ordering Information Product Literature

  ADEMCO’s 5809 wireless fixed heat and rate-of-rise temperature sensor offers expanded fire detection and installation flexibility. It is ideal for hard to wire locations and applications that require more than smoke detection. With no wires to run, the 5809 is fast and easy to install. The 5809 combines both rate-of-rise and fixed temperature sensors. Fires typically cause a rapid rise in temperature in the surrounding area. The 5809’s rate-of-rise thermostat senses the rise in temperature and signals an alarm if the increase is 15° or more per minute. A built-in fixed temperature sensor will also signal an alarm if the environmental temperature rises above 135°F. The 5809 is UL Listed (UL521) and CSFM approved for commercial and residential applications. The 5809 is UL Listed (UL521) and CSFM approved for commercial and residential applications. Contains a built-in transmitter which can send alarm, supervisory and battery condition messages to the system’s receiver/control unit Powered by a three-volt lithium battery. If the battery voltage gets too low, the 5809 sends a low battery signal to the control panel Features a tamper switch, which causes a trouble signal to be sent to the control if the unit is removed from the mounting base UL Listed for Commercial (when using 5881EH Receiver) or Residential applications VistaCom-kt4 Ordering Information Product Literature Commercial fire/burglary control and cost savings by eliminating a dedicated phone line VISTA-128FBP Fire/Burglary Control Panel 6160CR Commercial Fire Keypad 7845CF Cellular Fire Radio At System Sensor, innovation is more than an ideal; innovation is our way of life. Every day we design fire, carbon monoxide and heat detection and notification devices that use the most innovative technologies in the most inventive ways. We create products for our customers that are convenient to install, efficient to operate and offer the highest level of reliability. In other words, we make it our business to develop advanced ideas that deliver advanced solutions. Conventional Detection Audible/Visible Notification HVAC Systems Monitoring Sprinkler Systems Monitoring Intelligent Detection The System Sensor CO1224 carbon monoxide detector safeguards life with its electrochemical sensing technology, the industry’s most reliable technology that accurately measures and provides early warning of carbon monoxide levels in the air. We offer the broadest lines in conventional smoke detection. Our new i3™ Series takes a unique approach toward reducing costs with its installation ease, intelligence, and instant inspection. And our carbon monoxide, heat and beam detectors provide an effective solution when specialty detection is required. Conventional Detection Series: 100 Series Type: Plug-in Smoke Detector Model: 2151 Description: The 2151 is a low profile, plug-in photoelectric smoke detector. Data Sheet Installation Instructions 2-Wire Compatibility Manufacturers and Models Table Printer Friendly Specifications: 2151 Detection: Photoelectric Operating Voltage: (Mounting Base Dependent) Alarm Current: (Mounting Base Dependent) Temperature Range: 32° to 120°F (0° to 49°C) Humidity Range: 10% to 93% RH, noncondensing Dimensions: 2.0″ (51mm) H x 4.1″ (104mm) Dia. (unflanged base) or 6.1″ (155mm) Dia. flanged base Weight: 3.1 oz. (88 g) Conventional Detection Series: 400 Series Type: Plug-in Smoke Detector Model: 1451 Description: The 1451 is a plug-in ionization smoke detector. Installation Instructions 2-Wire Compatibility Manufacturers and Models Table Printer Friendly Specifications: 1451 Detection: Ionization Operating Voltage: (Mounting Base Dependent) Alarm Current: (Mounting Base Dependent) Standby Current: 120 µA max. Temperature Range: 32° to 120°F (0° to 49°C) Humidity Range: 10% to 93% RH, noncondensing UL Listed Velocity Range: 1200 fpm max. Sensitivity: 1.9% ± 0.6%/ft. nominal Dimensions: 3.2″ (8.1cm) H x 4.0″ (10.2cm) Dia. (unflanged base) or 6.2″ (15.7cm) Dia. flanged base Weight: 0.5 lb. (227 g) Conventional Detection Series: 400 Series Type: Direct-Wire Smoke Detector Model: 1400 Description: The 1400 is a 2-wire, ionization smoke detector. Installation Instructions 2-Wire Compatibility Manufacturers and Models Table Printer Friendly Specifications: 1400 Conventional Detection Series: 400 Series Type: Plug-in Heat Detector Model: 4451HT Description: The 4451HT is a high-temperature plug-in heat detector. Installation Instructions 2-Wire Compatibility Manufacturers and Models Table Printer Friendly Specifications: 4451HT Detection: Heat Heat Sensor: 190°F (88°C) fixed Operating Voltage: (Mounting Base Dependent) Alarm Current: (Mounting Base Dependent) Standby Current: 100 µA Temperature Range: 32° to 150°F (0° to 66°C) Humidity Range: 10% to 93% RH, noncondensing Wiring Gauge: 12-18 AWG, twisted pair recommended Dimensions: 2.1″ (53mm) H x 4.1″ (104mm) Dia. Weight: 5 oz. (150 g) 5623 Data Sheet (pdf) Installation Instructions (pdf) 135°F Fixed Temp, Dual-Circuit Mechanical Heat Detector 5624 Data Sheet (pdf) Installation Instructions (pdf) 194°F Fixed Temp, Dual-Circuit Mechanical Heat Detector 4451HT Data Sheet (pdf) Installation Instructions (pdf) The 4451HT is a high-temperature plug-in heat detector. 5451 Data Sheet (pdf) Installation Instructions (pdf) The 5451 is a combination fixed and rate-of-rise, plug-in heat detector. 5601P Data Sheet (pdf) Installation Instructions (pdf) 135°F Fixed Temp/Rate-of-Rise, Single-Circuit Mechanical Heat Detector with Plain Housing Why Beam Smoke Detection? Beam smoke detection provides better coverage for high-ceiling or large open areas where spot detectors are not well suited, such as churches, warehouses, atriums and barns. In addition, depending upon the application, beam smoke detection is more economical than spot detection. The Beam responds fast to all types of fires, works with all colors of smoke, including black, and better addresses stratification concerns. Better Coverage for Large Open Areas BEAM DETECTION OFFERS 20 TIMES THE COVERAGE OF A SINGLE SPOT-TYPE SMOKE DETECTOR! The 5600 Series Mechanical Heat Detectors HOME Copyright © 2006 System Sensor. All rights reserved. Why Mechanical Heat Detection? System Sensor’s 5600 series mechanical heat detectors are ideal for property protection against fire and for non-life-safety installations where smoke detectors are inappropriate due to: Excessive steam, moisture, dust, humidity or temperature Typical applications include: Residential, such as kitchens, attics and garages. Commercial, such as warehouses, storage facilities, restaurant kitchens, elevator machine rooms, elevator shafts and electrical closets. Clear Visual Indication 5600 series mechanical heat detectors feature clear visual indication of the activation method and temperature rating. Seven models have simple-to-read alpha-numeric text on the exterior. One model (5601P) has no letters, numbers or markings on the exterior. It is ideal for residential applications where external markings may compromise the visual integrity of the product and its surroundings. 5600 Series Configurations 5600 series mechanical heat detectors are available in multiple configurations to satisfy a broad range of installations: Single- and dual-circuit models Fixed temperature and combination Fixed temperature/rate-of-rise 135ºF or 194ºF ratings 5600 Series Model Numbers Model # Description 5601P Single circuit, Fixed/ROR, 135°F “Unmarked” 5602 Single circuit, Fixed/ROR, 194°F 5603 Single circuit, Fixed 135°F 5604 Single circuit, Fixed 194°F 5621 Dual circuit, Fixed/ROR, 135°F 5622 Dual circuit, Fixed/ROR, 194°F 5623 Dual circuit, Fixed 135°F 5624 Dual circuit, Fixed 194°F Operating Principles Rate-of-Rise (ROR) The ROR function will initiate an alarm when the rate of temperature increase exceeds 15 degrees Fahrenheit per minute. The air inside the chamber (dome) expands faster than it can escape. The increasing pressure inside the chamber begins to depress a thin diaphragm, which, in turn closes the contact and initiates a fire alarm condition. The ROR function is restorable and can be tested. Care should be taken so the temperature does not exceed the fixed temperature element. Operating Principles Fixed temperature Every 5600 series model has a circular external heat collector. The fusible alloy of the external collector will melt and initiate an alarm when the temperature surrounding the detector reaches a predetermined level (either 135 degrees Fahrenheit or 194 degrees Fahrenheit). The external collector will be released from the dome of the unit and cause an internal diaphragm to depress the integral alarm contact. The fixed temperature function is not restorable because the external heat collector has been destroyed and, therefore, cannot be tested. 5600 Series Installation Advantages 5600 series mechanical heat detector features make installation easy by: Using SEMS-type Philips-head terminal screws to provide an easier and more positive wiring connection. Having conductors that are clamped by the SEMS-type terminals instead of wrapping a conductor around a screw, a method used by other manufacturers. Accommodating 14 to 22 AWG conductors. 5600 Series Installation Advantages 5600 series mechanical heat detectors mount to the most common back boxes, including: Single-gang 3.5″ and 4″ octagonal 4″ square back box with square to round plaster ring A reversible mounting base accommodates surface and flush mount installations. 5600 Series Mechanical Heat Detectors System Sensor’s 5600 series mechanical heat detectors provide an effective solution when specialty detection is required What Is Sprinkler Systems Monitoring? Sprinkler systems monitoring is the monitoring of water flow, pressure and valve positions within a sprinkler system. Wet Pipe Sprinkler System Sprinkler Monitoring Devices Sprinkler monitoring devices monitor condition variances within the sprinkler system. System Sensor product categories: Waterflow detectors Pressure switches Supervisory switches Explosion proof models are available for all System Sensor sprinkler monitoring devices. Fire Sprinkler System Types Two main types of systems: Wet pipe (most common) Dry pipe Wet Pipe Sprinkler Systems Wet pipe systems are: Filled with water at all times. Best suited in areas where pipes are not subject to freezing temperatures or accidental discharge. With a wet pipe system: Heat from fire causes an operating element in the sprinkler head to activate, resulting in water being discharged. Water discharges only through sprinklers that have been exposed to the high temperatures from a fire. Wet Pipe Sprinkler Systems Devices that typically comprise a wet pipe system include: Waterflow detectors that monitor the flow of water within the pipe. Supervisory switches that monitor the open valve positions, which ensure the system is operable during a fire condition. Alarm pressure switches that are sometimes used to monitor water flow. Dry Pipe Sprinkler Systems Dry pipe systems: Are filled with water only during activation. Contain compressed air to hold back water. Are best suited in areas that are subject to freezing temperatures. With a dry pipe system: When a sprinkler head opens, air in the pipe releases and a valve opens, allowing water to fill the system. An activated sprinkler causes the system’s pressure to change, which activates a pressure switch, then activates an alarm at the panel. Water discharges only through sprinklers that have been exposed to the high temperatures from a fire. Dry Pipe Sprinkler Systems Devices that typically comprise a dry pipe system include: Supervisory pressure switches that monitor the pressure level. If the pressure falls too low, the air pressure regulator turns the air compressor on to add pressure to the system. If the system pressure rises too high, air will be drained from the system. In each case, the pressure switch sends a trouble signal to the releasing panel. Alarm pressure switches that detect the activation of a sprinkler head. When air pressure drops too quickly, an alarm is activated. This loss of pressure will over-power the abilities of the pump that adds pressure to the system. Supervisory switches that monitor the positions of the valves, ensuring the system is operable during a fire condition. Waterflow Detectors Waterflow detectors monitor the water flow within a fire sprinkler system that is caused by the activation of a sprinkler head. System Sensor waterflow detectors: WFD Conventional WFDT – Branch line signaling and residential WFDTH – Residential Waterflow Detectors Conventional saddle type waterflow detectors: Are available for pipes sized two inches to eight inches. Include models WFD20, WFD25, WFD30-2, WFD35, WFD40, WFD50, WFD60 and WFD80. Are often installed in riser applications: risers are the vertical supply pipes in a sprinkler system. Use floor control assemblies, as pictured. Are compatible with Schedule 10 & 40 pipe. Enclosure specifications are: NEMA 4 UL listed for indoor/outdoor applications T-tap models T-tap models (branch line and residential detectors): Include System Sensor models WFDT, WFDTH and WFDTNR. Are designed for “thread-in” applications, which are compatible with a one inch NPT. Also, 12 paddles are offered for a variety of pipe material and sizes. Primary signalling in residential systems and branch line signalling in larger systems. Are resistant to tampering. Enclosure specifications are: NEMA 4 (WFDT only). UL listed for indoor/outdoor applications. T-tap models WFDTH Indicates a discharge from a sprinkler head. Is designed for primary signaling in residential systems. Fits within standard 2×4 stud wall construction. Has the same electrical and mechanical characteristics as the WFDT. WFDTNR Is used primarily in residential applications. Is identical to the WFDT and WFDTH, but does not have a mechanical retard. Waterflow Detectors Unique water flow product features include: Field-replaceable terminal block with front mounted terminals. Field-replaceable retard mechanism. No need to drain the entire system. New delay adjustment dial. More user-friendly with the approximate delay in seconds posted directly on the dial. Two 1/2 inch conduit openings. One open One knock-out type Wiring diagrams on the inside cover and on the terminal block. Pressure Switches Alarm pressure switches (EPS10 series): Sense water flow in the piping, which is caused by discharge from a sprinkler head. Are available in one- and two-switch models. Include System Sensor models EPS10-1 and EPS10-2. Supervisory pressure switches (EPS40 and EPS120 series): Monitor and help maintain a desired pressure level within the system. Are available in one- and two-switch models. Include System Sensor models EPS40-1, EPS40-2, EPS120-1 and EPS120-2. Are most commonly used in dry pipe systems. Cover a range of pressure ratings from 4-20 psi to 10-200 psi. Supervisory Switches Supervisory switches monitor the open position of valves used in a sprinkler system. Three styles of supervisory switches are: OSY2: Outside Screw & Yoke PIBV2: Post Indicator and Butterfly Valve PSP1: Special Purpose OSY2 Supervisory Switches OSY2: Requires fewer and less expensive conduit fittings for an electrical connection. Has a rugged mounting bracket that does not bend. Offers larger diameter carriage bolts that allow the OSY2 to securely mount on valves. Has wiring diagrams on the inside cover of the device. PIBV2 Supervisory Switches PIBV2: Requires fewer and less expensive conduit fittings for an electrical connection. Offers bi-directional mounting that allows for reverse action of the switch to accommodate both rising and falling flag installations. Has a new, longer actuating arm with a breakaway feature, as pictured. Has wiring diagrams on the inside cover of the device. PSP1 Supervisory Switches PSP1: Has a versatile 360 degree mounting option. Has a plug that snaps securely into the jack. Works where other switches will not, providing a solution for every application. Explosion Proof Sprinkler Monitoring Products Explosion proof products: Are designed for installation in hazardous locations. System Sensor offers a full line of explosion proof products, including: Waterflow detectors Pressure switches Supervisory switches Explosion Proof Sprinkler Monitoring Products Explosion proof waterflow detectors and pressure switches are classified as follows: Class I, Groups B, C and D, Divisions 1 and 2 Class II, Groups E, F and G, Divisions 1 and 2 Class III, Divisions 1 and 2 WFDEXP model numbers include: WFD20EXP, WFD25EXP, WFD30-2EXP, WFD35EXP, WFD40EXP, WFD50EXP, WFD60EXP and WFD80EXP EPSEXP model numbers include: EPS10EXP, EPS40EXP and EPS120EXP Explosion Proof Sprinkler Monitoring Products Explosion proof supervisory switches are classified as follows: Class I, Groups C and D, Divisions 1 and 2 Class II, Groups E, F and G, Divisions 1 and 2 Model numbers include: OSYEXP: Outside Screw and Yoke PIBVEXP: Post Indicator or Butterfly Valve Sprinkler Alarm Notification Products PDRP Series Fire Alarm Control Panel PDRP-1001 Two-zone pre-action/deluge. Initiating and release circuit fault & fuse protection with up to 90 hours of standby. Outdoor Horn/Strobe – P12015K UL outdoor listed. Watertight when used with the WBB weatherproof back box. 120 VAC, 15 candela. Alarm Bells SSV series (120VAC) & SSM series (24VDC). Available in 6 inch, 8 inch and 10 inch. 80dB+ sound output. Conventional Detection Audible/Visible Notification HVAC Systems Monitoring Sprinkler Systems Monitoring Intelligent Detection Intelligent Detection Product Line Smoke Detectors • Duct Smoke Detectors • Beam Smoke Detectors • Thermal Eclipse • Modules • Bases • Pinnacle • Filtrex • Acclimate • Accessories System Sensor’s intelligent smoke detectors use advanced communications protocols to ensure accuracy and stability. Sophisticated software provides false alarm reduction and automatically monitors detector sensitivity. Extensive research and development allow us to optimize technologies based on environment and risk. Take a look at laser technology used in clean rooms and communications centers, difficult environment smoke detectors for dusty or dirty facilities, multi-criteria devices for areas requiring stability and performance and intrinsically safe smoke detectors for hazardous environments. Acclimate Brochure Pinnacle Brochure ED-PTI Data Sheet (pdf) Installation Instructions (pdf) Eclipse Series Photoelectric Smoke Detector with Thermal and Built-in Isolator ED-T Data Sheet (pdf) Installation Instructions (pdf) Eclipse Series Fixed Temperature/Rate-of-Rise/High-Temperature Thermal Detector ED-TI Data Sheet (pdf) Installation Instructions (pdf) Eclipse Series Fixed Temperature/Rate-of-Rise/High-Temperature Thermal Detector with Built-in Isolator Conventional Detection Audible/Visible Notification HVAC Systems Monitoring Sprinkler Systems Monitoring Intelligent Detection Intelligent Detection Product Line Smoke Detectors • Duct Smoke Detectors • Beam Smoke Detectors • Thermal Eclipse • Modules • Bases • Pinnacle • Filtrex • Acclimate • Accessories Intelligent Detection Series: Eclipse Type: Intelligent Smoke Detector Model: ED-T Description: Eclipse Series Fixed Temperature/Rate-of-Rise/High-Temperature Thermal Detector Data Sheet Installation Instructions Printer Friendly Specifications: ED-T Operating Temperature Range: Thermal: -4° to 100°F (-20° to 38°C), 135° to 174°F setpoint; High-Temp: -4 to 150°F (-20° to 66°C), 175° to 190°F setpoint Operating Humidity Range: 10% to 93% RH noncondensing Dimensions: 4.1″ Dia., 2.1″ High in EB base Thermal Ratings: 135°F (57°C) fixed temperature setpoint; 15°F (8.3°C) per min. rate-of-rise; 190°F (88°C) high-temp Shipping Weight: 4.8 oz. (136 g) Voltage Range: 15 – 30 volts DC peak Standby Ratings: 451 µA @ 24 VDC (continuous broadcasts)